Access Router Login →

Click to see login instructions and access your router

192.168.50.1 is the most popularly used private IP address for accessing the router administration panels globally. This default gateway IP address acts as an entry point to your router's admin panel. This is where you can manage all aspects of the configuration which is required for your office or home network.

Many router brands including ASUS, Netgear, D-Link, TP-Link, Linksys use 192.168.50.1 as their default gateway address. When you type this IP address into your web browser address bar while connected to your network then you will be navigated to your router's login page.

Through this admin interface, you can perform necessary tasks such as changing your WiFi password, updating the network name(SSID), setting up parental controls, configuring security protocols, updating software, port forwarding, setting up guests network and much more advanced networking features.

The 192.168.50.1 address belongs to the private IP range defined by RFC 1918, meaning it cannot be accessed from the public internet, providing an additional layer of security for your network configuration.

UserName	Password	Probability
admin	admin	60%
admin	password	25%
admin		15%

ASUS Netgear D-Link TP-Link Linksys

1. Connect the computer or a device to your router via WiFi or Ethernet cable. If possible prefer wired connection over WiFi to avoid suddenly getting logged off.
2. Open a web browser - it can be any browser like Chrome, Firefox, Safari, Bing, etc.
3. Type 192.168.50.1 in the address bar - if it's navigated to a blank page then type https://192.168.50.1 then hit enter
4. In the Login page enter your Username and Password the click Login to access the admin portal.

If you're facing trouble accessing 192.168.50.1, try these solutions:

• Confirm that you are properly connected your computer or a device to your router's WiFi or via Ethernet cable
• Use http://192.168.50.1 instead of https://
• Check if your router uses a different IP (run ipconfig on Windows or ifconfig on Mac/Linux)
• VPN connections can block access to local router admin pages
• Sometimes browser extensions may intrude and cause problems - so, try a different browser
• Make sure your router is powered on and all indicator lights are functioning
• If you are using multiple routers then disconnect extra routers temproarily and connect with the main router.
• Cache sometimes blocks the router access (Try Ctrl+Shift+R in windows, Cmd+Shift+R in mac or use Incognito window).
• If the above steps not worked out then try factory reset.
• If Login/Admin page loads but Dashboard is blank or showing any error then disable antivirus, disable browser extensions, update router software(if possible).
• Still can't access :ip? Common final causes would be
  • Router firmware corrupted
  • Wrong IP
  • Damaged Router
  • ISP provided Router with blocked admin access
  • Corporate network restrictions

TP-Link routers are among the most popular worldwide. If you're having trouble accessing your TP-Link router at 192.168.50.1, follow this dedicated troubleshooting guide.

1. Default TP-Link Router IPs

• 192.168.0.1 - Most Archer & TL-WR models
• 192.168.1.1 - Some newer models
• tplinkwifi.net - Newer firmware

2. TP-Link Default Login Credentials

3. Use tplinkwifi.net Instead of IP

If you are using new TP-Link firmware then try opening http://tplinkwifi.net. If this loads but IP does not, it means:

• DNS is working
• IP conflict or LAN IP mismatch exists

4. TP-Link Login Page Not Opening

If login page doesn't load:

• Ensure device is connected to TP-Link Wi-Fi
• Disable VPN/Proxy/Antivirus temporarily
• Clear browser cache or use Incognito window
• Try Ethernet cable

5. TP-Link Router in Access Point (AP) Mode

If TP-Link is in AP Mode, router login IP changes:

• IP 192.168.50.1 doesn't work
• No WAN settings
• Router doesn't assign IP

Fix:

• Connect to main router
• Find TP-Link IP from connected devices list
• Access that IP instead

To revert:

Advanced → Operation Mode → Wireless Router Mode

6. TP-Link WAN Connection Issues

• WAN cable plugged into LAN port
• Wrong connection type selected
• PPPoE credentials missing

Fix: Go to Advanced → Network → Internet. Select correct type: Dynamic IP / PPPoE / Static IP. Save and reboot router.

7. TP-Link Router Connected but No Internet Access

• Change DNS to 8.8.8.8 / 8.8.4.4
• Enable NAT
• Disable MAC address clone
• Restart modem, then router, then device

8. TP-Link Firmware Update Issues

Firmware update issues include update stuck, router reboots continuously, firmware rejected.

Fix:

• Download exact firmware for your model
• Use Ethernet cable only
• Disable antivirus
• Reset router then reattempt firmware update

9. TP-Link Router Wi-Fi Slow or Dropping

• Enable smart connect (in dual-band routers)
• Change Wi-Fi channel: 2.4 GHz - Channel 1/6/11, 5 GHz - Channel 36/40/44/48
• Disable QoS temporarily
• Disable OneMesh for testing
• Update firmware

10. TP-Link Router Keeps Rebooting

Possible causes:

• Overheating
• Faulty power adapter
• Corrupt firmware
• Too many connected devices

Fix:

• Power off for 5 minutes
• Improve ventilation
• Try different power adapter
• Factory reset router

11. TP-Link Factory Reset

Reset only when none of the above works. This erases all settings.

1. Press RESET button
2. Hold 10–15 seconds
3. Router reboots
4. Setup router again

After reset try http://192.168.0.1 or http://tplinkwifi.net

Avoid IP Conflicts

If we have two routers in our network, for example: a main router and a range extender and both use the same default IP (ex: 192.168.50.1) can conflict, causing connection issues. Changing any one of the routers IP solves this issue.

Network Design and Organisation

Most businesses or tech users may want to organise their network into segments. For example:

• 192.168.10.x for Office PCs
• 192.168.20.x for IoT or CCTV Cameras
• 192.168.30.x for Guests

To define those segments clearly, changing the gateway IP address is the best option.

Security and Privacy reasons

Changing the router's IP from default to another private IP can reduce exposure to automated login attempts or basic scanning tools.

10.0.0.1 10.0.0.2 10.10.10.254 192.168.0.1 192.168.0.254 192.168.1.1

192.168.I.1 192.168.l.1 192.168.O.1