Access Router Login →

Click to see login instructions and access your router

192.168.0.10 is the most popularly used private IP address for accessing the router administration panels globally. This default gateway IP address acts as an entry point to your router's admin panel. This is where you can manage all aspects of the configuration which is required for your office or home network.

Many router brands including Netgear, D-Link, Linksys, ISP Router use 192.168.0.10 as their default gateway address. When you type this IP address into your web browser address bar while connected to your network then you will be navigated to your router's login page.

Through this admin interface, you can perform necessary tasks such as changing your WiFi password, updating the network name(SSID), setting up parental controls, configuring security protocols, updating software, port forwarding, setting up guests network and much more advanced networking features.

The 192.168.0.10 address belongs to the private IP range defined by RFC 1918, meaning it cannot be accessed from the public internet, providing an additional layer of security for your network configuration.

UserName	Password	Probability
admin	admin	40%
admin	password	30%
admin		20%
	admin	10%

Netgear D-Link Linksys ISP Router

1. Connect the computer or a device to your router via WiFi or Ethernet cable. If possible prefer wired connection over WiFi to avoid suddenly getting logged off.
2. Open a web browser - it can be any browser like Chrome, Firefox, Safari, Bing, etc.
3. Type 192.168.0.10 in the address bar - if it's navigated to a blank page then type https://192.168.0.10 then hit enter
4. In the Login page enter your Username and Password the click Login to access the admin portal.

If you're facing trouble accessing 192.168.0.10, try these solutions:

• Confirm that you are properly connected your computer or a device to your router's WiFi or via Ethernet cable
• Use http://192.168.0.10 instead of https://
• Check if your router uses a different IP (run ipconfig on Windows or ifconfig on Mac/Linux)
• VPN connections can block access to local router admin pages
• Sometimes browser extensions may intrude and cause problems - so, try a different browser
• Make sure your router is powered on and all indicator lights are functioning
• If you are using multiple routers then disconnect extra routers temproarily and connect with the main router.
• Cache sometimes blocks the router access (Try Ctrl+Shift+R in windows, Cmd+Shift+R in mac or use Incognito window).
• If the above steps not worked out then try factory reset.
• If Login/Admin page loads but Dashboard is blank or showing any error then disable antivirus, disable browser extensions, update router software(if possible).
• Still can't access :ip? Common final causes would be
  • Router firmware corrupted
  • Wrong IP
  • Damaged Router
  • ISP provided Router with blocked admin access
  • Corporate network restrictions

D-Link routers are mostly used in homes and by ISPs, commonly using 192.168.0.10 as a default gateway. If you are unable to access your D-Link router's admin page then follow the below given steps.

1. Confirm the Correct D-Link Router IP Address

• 192.168.0.1 (most D-Link routers)
• 192.168.1.1 (newer or ISP-configured routers)
• dlinkrouter.local
• 192.168.11.1 (Custom LAN IP)

2. D-Link Default Login Credentials

Login issues are common due to incorrect credentials.

3. Use dlinkrouter.local Instead of IP

Many newer D-Link routers support: http://dlinkrouter.local — If this works but the IP doesn't, then:

• LAN IP may have changed
• DNS is resolving correctly
• IP conflict may exist

4. D-Link Router Login Page is Not Loading

Try the below steps:

• Confirm device is connected to D-Link Wi-Fi / LAN
• Disable VPN, proxy, antivirus temporarily
• Try http://192.168.11.1 or http://192.168.0.1 or http://dlinkrouter.local
• Clear browser cache / use incognito
• Preferred wired Ethernet connection over Wi-Fi

5. D-Link Router in Bridge / AP Mode

Admin page is unreachable when the router is in Bridge or AP mode.

• Connect to the main router
• Find D-Link IP in connected devices then access with that IP
• To revert: Settings → Operation Mode → Router Mode

6. D-Link Internet Not Working

Due to any one of the below reasons:

• WAN cable connected to LAN port
• Wrong internet connection type
• PPPoE credentials missing

Fix: Go to Settings → Internet → WAN then select correct type:

• Dynamic IP (Cable)
• PPPoE (Fiber)
• Static IP (Corporate)

7. D-Link Connected but No Internet

• Change DNS to 8.8.8.8, 8.8.4.4
• Disable Advanced QoS temporarily
• Disable MAC Address Filtering
• Restart modem → router → device (order matters)

8. D-Link Firmware Update Problems

Firmware upload failed, router stuck after update, or continuous reboot loop:

• Download the exact firmware which matches your model
• Use Ethernet only
• Disable antivirus
• Don't power off during update
• Reset router and retry

9. D-Link Wi-Fi Slow or Unstable

• Set Wi-Fi mode to 802.11n/ac/ax only
• Change channels: 2.4 GHz → 1 / 6 / 11
• Change channels: 5 GHz → 36 / 40 / 44 / 48
• Disable Smart QoS temporarily
• Turn off WPS if unused
• Update firmware

10. D-Link Router Keeps Restarting

Probable reasons:

• Overheating
• Faulty power adapter
• Firmware corruption
• Electrical fluctuations

Fix:

• Power off for 5 minutes
• Improve ventilation
• Use original adapter
• Factory reset

11. D-Link Factory Reset

Note: This will erase all settings.

1. Hold RESET button for 10–15 seconds
2. Router reboots
3. Setup again from scratch

Access http://192.168.1.1 or http://dlinkrouter.local after reset.

12. D-Link LED Light Meanings

Note: LED meanings may vary by model.

Netgear routers are widely used in homes and offices. If you're unable to access the Netgear router admin panel at 192.168.0.10, follow this dedicated troubleshooting guide.

1. Confirm the Correct Netgear Router IP Address

Netgear routers typically use one of the following default IP addresses:

• 192.168.1.1 (Most Netgear models)
• 192.168.0.1 (Alternate default)
• 10.0.0.1 (Orbi and some mesh routers)
• routerlogin.net or routerlogin.com (Netgear's web-based login)

2. Netgear Default Login Credentials

If you're having trouble logging in, try these default credentials:

macOS:
netstat -nr | grep default
Look for the "default" row - that's your router IP.

Windows:
Open Command Prompt and run ipconfig

3. Use routerlogin.net Instead of IP

If the IP address doesn't work, try accessing your router via:

• http://routerlogin.net
• http://routerlogin.com

4. Netgear Router Login Page Not Loading

If the login page doesn't load:

• Username: admin
• Password: password

Tip: The default password is case-sensitive. Try "password" (all lowercase).

5. Netgear App Not Connecting

If the Netgear Nighthawk or Orbi app isn't working:

• Make sure your phone is connected to the router's Wi-Fi
• Update the app to the latest version
• Restart both the router and your phone

6. Netgear Internet Not Working

If your internet isn't working:

Fix: Try using a wired Ethernet connection instead of Wi-Fi to access the router admin panel.

7. Netgear Factory Reset

Warning: This erases all settings including Wi-Fi name and password.

1. Locate the Reset button (small hole on back)
2. Press and hold with a paperclip for 7-10 seconds
3. Wait for router to reboot (about 2 minutes)

8. Double NAT / ISP Modem Issue

If you have both an ISP modem/router and a Netgear router:

• Put ISP modem in bridge mode, or
• Put Netgear router in AP (Access Point) mode

9. Netgear-Specific URLs

• http://routerlogin.net
• http://routerlogin.com
• http://192.168.1.1/start.htm
• http://192.168.1.1/index.htm
• http://192.168.1.1/basic_home.htm

10. Hardware Failure Signs

Signs that your router may have hardware issues:

• Router gets very hot even with good ventilation
• LEDs behave erratically or don't light up
• Router keeps rebooting on its own

11. Netgear LED Light Meanings

12. Nighthawk / Orbi App Issues

If you're having trouble with the Netgear app:

• Make sure your phone is connected to the router's Wi-Fi (not mobile data)
• Update the Nighthawk or Orbi app to the latest version
• Restart both the router and your phone
• Try accessing via browser at routerlogin.net instead

13. Quick Fixes Summary

• Power cycle: Unplug router, wait 30 seconds, plug back in
• Check cables: Ensure all connections are secure
• Update firmware: Keep router software current
• Contact Netgear support if issues persist

Avoid IP Conflicts

If we have two routers in our network, for example: a main router and a range extender and both use the same default IP (ex: 192.168.0.10) can conflict, causing connection issues. Changing any one of the routers IP solves this issue.

Network Design and Organisation

Most businesses or tech users may want to organise their network into segments. For example:

• 192.168.10.x for Office PCs
• 192.168.20.x for IoT or CCTV Cameras
• 192.168.30.x for Guests

To define those segments clearly, changing the gateway IP address is the best option.

Security and Privacy reasons

Changing the router's IP from default to another private IP can reduce exposure to automated login attempts or basic scanning tools.

10.0.0.1 10.0.0.1/admin 10.0.0.138 10.0.0.2 10.0.1.1 10.1.1.1

192.168.I.1 192.168.l.1 192.168.O.1