192.168.1.2 — Login Guide (Secondary Router, AP Mode & Client Device)

Click to see login instructions and access your router

1. Connect the computer or a device to your router via WiFi or Ethernet cable. If possible prefer wired connection over WiFi to avoid suddenly getting logged off.
2. Open a web browser - it can be any browser like Chrome, Firefox, Safari, Bing, etc.
3. Type 192.168.1.2 in the address bar - if it's navigated to a blank page then type https://192.168.1.2 then hit enter
4. In the Login page enter your Username and Password the click Login to access the admin portal.

ℹ 192.168.1.2 is usually NOT a router's admin IP

On most home networks, the router itself sits at 192.168.1.1, and 192.168.1.2 is the first client device (computer, phone, printer, IoT gadget) that connects to the network. If you're looking for your router's login page, try 192.168.1.1 instead.

192.168.1.2 is a private IPv4 address in the RFC 1918 range (192.168.0.0/16). Unlike its more famous neighbour 192.168.1.1 — which is one of the most common router gateway IPs — 192.168.1.2 is almost always a client device, not a router admin interface.

If you're seeing 192.168.1.2 on your network, it usually falls into one of three scenarios:

Scenario 1 — A client device (most common)

Your home router's DHCP server usually starts assigning addresses at 192.168.1.2 for the first device that connects. So if your router is at 192.168.1.1, then 192.168.1.2 is almost certainly a laptop, phone, smart TV, printer, or IoT device on your network. It does NOT have an admin login page — it's just an endpoint.

Scenario 2 — A secondary router or wireless access point (cascade mode)

If you have a second router or a dedicated wireless access point wired behind your primary router (a common home-network setup for extending Wi-Fi range), the secondary device may have been assigned 192.168.1.2 as its LAN IP. In this case, you can log in at http://192.168.1.2 to configure the secondary device. Default credentials vary by manufacturer — try the standard combinations in the credentials table above.

Scenario 3 — A local server (school or office network)

In institutional networks, 192.168.1.2 is sometimes assigned to a local server. A well-known example is Indonesian schools, where 192.168.1.2 is often the Computer-Based Test (CBT) server IP for national exam systems (UNBK). In this case, the "login" is to the CBT application, not to a router — your school's IT department will have provided the correct credentials.

If you've confirmed that 192.168.1.2 is your secondary router, access point, or a device with a web admin panel, log in with these steps:

1. Connect your computer or phone to the same network as the device (Wi-Fi or Ethernet).
2. Open a browser and type http://192.168.1.2 in the address bar.
3. Enter default credentials from the table above (admin/admin is most common).
4. If none of the defaults work, check the sticker on the device — many manufacturers ship unique passwords per device.

If http://192.168.1.2 doesn't load at all, the IP is likely not a login target — the device at 192.168.1.2 is probably a client (computer/phone/IoT) and you're looking for the wrong address. Try 192.168.1.1 instead.

Q: My phone shows its IP as 192.168.1.2 — is that a problem?

No, that's normal. It just means your phone was the first device to connect to the network after the router booted, so the router's DHCP server assigned it 192.168.1.2 (the first address after the router's own 192.168.1.1). It's not a problem and doesn't need to be changed.

Q: I typed 192.168.1.2 in my browser and nothing loads. Why?

Because there is usually no web server at 192.168.1.2 — client devices (phones, laptops) don't run admin panels. You probably want to reach your router's admin page, which is almost always at 192.168.1.1. Try that IP instead.

Q: I have two routers — how do I access the second one?

If the second router (or access point) is in cascade mode behind your primary router, it may have been given the LAN IP 192.168.1.2. In that case, type http://192.168.1.2 in a browser while connected to the network, and try the default credentials in the table above.

Q: Is 192.168.1.2 the same as 192.168.1.1?

No — they are two different addresses on the same subnet. In a standard home setup, 192.168.1.1 is the router, and 192.168.1.2 is the first connected client device. Both are private IP addresses in the RFC 1918 range (192.168.0.0/16).

Q: What is Garuda CBT / UNBK related to 192.168.1.2?

In Indonesia, UNBK (Ujian Nasional Berbasis Komputer — Computer-Based National Exam) and related test platforms are often deployed on local school networks with the test server at 192.168.1.2. Students access the test through a browser at that IP. If you're a student or teacher trying to reach a CBT server, the "login" you're looking for is the test application's login — your school's IT staff have the correct credentials. This is not a router login.

Avoid IP Conflicts

If we have two routers in our network, for example: a main router and a range extender and both use the same default IP (ex: 192.168.1.2) can conflict, causing connection issues. Changing any one of the routers IP solves this issue.

Network Design and Organisation

Most businesses or tech users may want to organise their network into segments. For example:

• 192.168.10.x for Office PCs
• 192.168.20.x for IoT or CCTV Cameras
• 192.168.30.x for Guests

To define those segments clearly, changing the gateway IP address is the best option.

Security and Privacy reasons

Changing the router's IP from default to another private IP can reduce exposure to automated login attempts or basic scanning tools.